Ritto 4630/01 compatible?

magnus · November 3, 2019, 8:20pm

Hello PatrikB78,

you wrote at RITTO 4630/02 success with a pre-beta. What is with your Ritto 4630/01?
Thank you very much.

patrickb78 · November 3, 2019, 9:49pm

Thanks for your hint. My fault. I was talking about my 4630/01.

magnus · November 3, 2019, 10:04pm

Hello @Juergen,
when is the release date of that pre-beta?

coolion32 · November 9, 2019, 10:17am

The new firmware repairs the Open function via App for the Ritto 4630/01. But ring to open is farther broken.

magnus · November 9, 2019, 6:22pm

Hi Erol,

thank you. What new firmware do you mean?

coolion32 · November 9, 2019, 7:22pm

1.2.4

magnus · November 9, 2019, 9:49pm

Hello @Juergen,

when do you release that 4630/01 compatibility of beta firmware 1.2.4?

Juergen · November 9, 2019, 10:07pm

If beta testing goes well within the next weeks.

magnus · November 19, 2019, 9:25pm

Hello @Juergen,

do you have some news?

Juergen · November 20, 2019, 9:16am

New firmware release is scheduled for this week. 4630 support has much improved: Most systems work out of the box with default settings, some need special parameters (Nuki support can help).

kosmonowt · November 20, 2019, 2:32pm

Thanks @Juergen !
Today I came to test it finally with my 4630/02.
It does work much better than before. So it recognizes the ring (which did not work before). I followed the wiring instruction and made sure it’s correct twice.

Anyhow, it can not open the lock at the gate (the button on my ritto works though). Also, I tried the 2-persons variant to configure it but it didn’t help either.

What else could I do to to configure it?

Btw, others in my compound use newer phones at the same bus. (If that makes any difference).

Any help is greatly appreciated, I believe it’s only the last bit of modification.

RuedigerW · November 21, 2019, 11:43am

Ich habe es heute auch mal an meiner 4630/2 getestet.
Beim Einrichten erkennt Nuki das drücken des Türöffners an der Sprechanlage aber nicht das klingeln an der Haustüre und kann die Türe auch nicht öffnen.
Opener Software 1.2.6

RuedigerW · November 23, 2019, 11:12am

Habe heute die Opener Version 1.2.7 installiert.
Einrichtung:
Der Opener erkennt das Drücken des Türöffners an der Sprechanlage und das Klingeln an der Haustüre.
Die Türe kann aber weder durch die App noch per klingeln geöffnet werden.

patrickb78 · November 23, 2019, 11:38am

I’ve changed the delay (Settings -> Administration -> Delay when opening [might be slightly different in english. On german it is “Verzögerung beim Öffnen”]) to 3 seconds. Since then Ring-To-Open works quite smooth

RuedigerW · November 23, 2019, 2:15pm

Hab´s probiert mit der Verzögerung - Türe öffnet trotzdem nicht.

RuedigerW · November 25, 2019, 2:59pm

Nach der Hilfe von Jürgen funktioniert jetzt alles bestens - danke.

tron1x · November 25, 2019, 3:12pm

@RuedigerW could you provide the necessary steps here? So everyone can have the advantages of it

RuedigerW · November 25, 2019, 3:27pm

Jürgen has worked here with different PIN numbers - I think the settings were individual. I do not want to publish the pin numbers. Please contact Jürgen.

Skrause · February 6, 2020, 11:09am

Hi guys.
Yesterday I’ve installed the Nuki Opener, Nuki Bridge with Nuki smart Lock. Everything’s working fine except the Ring to Open function. I have the Ritto 4630/01 . I have installed the newest Firmware 1.3.1.
Hope someone can help me. I can open the door with my Nuki app. But when I ring the door bell it won’t open ( I have set it to ring to open in the App) and i don’t get any notifications that my front door bell is ringing. Even that my Nuki web is activated.
Thanks …

RuedigerW · February 16, 2020, 10:54am

stelle mal “Delay to open” auf 3 sec.