Nuki Opener | Golmar T-940 Plus

[Georg_S (Georg Sixt)]

Golmar BUS systems are under investigation. We will release our results soon.

[cirmler (Christian Irmler)]

Hi Georg,

do you have any news?

Best, Chris

[Georg_S (Georg Sixt)]

Not yet, please be patient! Thanks

[cirmler (Christian Irmler)]

Been patient for another week, allow me to ask again if you have any update for Golmar Bus users.

[cirmler (Christian Irmler)]

May I kindly ask for an update for Golmar Bus users?

[Juergen (Jürgen Pansy)]

We have the system in our lab under observation. There is not more to say for the time beeing.

[Marlon_Bos]

@Juergen can you share anything new on the status of Golmar gear?

[Juergen (Jürgen Pansy)]

Sorry, no update for the time beeing. It’s still work in progress.

[Marlon_Bos]

Thanks for the heads up @Juergen! I think we’re just excited about it

[cirmler (Christian Irmler)]

Greetings to the team!
Is there any update so far?
Thanks, Christian

[cirmler (Christian Irmler)]

Waiting for months now as I bought the opener when it came out. You mentioned that the team is working on it an that you have a Golmar Intercom System in the labs.

Any progress so far?

Can we expect a beta this year?

Thanks for a quick update!

Best, Chris

[Juergen (Jürgen Pansy)]

Conexionado GOLMAR VESTA 2

There are some good and bad news: The good news are that we have it working in our lab an will be able to release it in a beta soon. The bad news are that a specific cabling is necessary which requires to place a resistor between two contacts. We will make instructions for this available here in the Dev Board, but it also means that Golmar Bus based intercoms will remain in beta for some time until an official „Golmar Adapter Cable“ (or similar) and all necessary modifications to the Apps are …

And

Nuki Opener firmware - beta release notes

Important Notes: In case you have a functioning setup, we do not recommend installing new beta versions. Beta versions are sometimes used to address and test certain intercom issues that may be inappropriate for others. Please also note that beta users will be removed from the beta after a certain period of time (usually 1 month). In case you have problems completing the configuration, doorbell recognition or electric strike actuation of your Nuki Opener, you must perform a reconfiguration (Ad…

[Tio_Rafiki (Rafael)]

Hi with this resistor and this diagram It will works nuki opene with a Goldman Platea PLUS ? The resistor 82 ohm of 1/4W or 1W ?¿

https://developer.nuki.io/uploads/short-url/cW6n7030BzQUnh542xbl9ZLexPA.pdf

And how can I install a Beta firmware ?

Thanks

[Georg_S (Georg Sixt)]

1/4W is OK, either send me your Opener ID via PM or wait for the live release,that will be available soon.
Best regards
Georg

[Michiel (Michiel Panders)]

Hi Georg, my opener is expected to arrive today and I would be keen to test it over the Christmas break. I have the 82 Ohm resistor ready to go . Could I get a copy of the beta sw ? The system I have is a Golmar Tekna Plus V2.

Thanks,
Michiel

[Georg_S (Georg Sixt)]

Hi Michiel,
you don’t need the beta, as we already released firmware version 1.3.1 live. Please connect the Opener as follows: Golmar Plus intercom system support

[Michiel (Michiel Panders)]

Awesome , thank you ! I will let you know how things went, happy holidays !

[cirmler (Christian Irmler)]

Hi Georg,

tried exactly as described (wiring and connection diagram), but unfortunately it still doesn’t work for me.

Here are the steps I did, maybe you can tell me if I made a mistake:

1. firmware update Opener went well V 1.3.1
2. reset Opener to factory settings in administration
3. added Opener to my system configuration
4. config asked me to connect to bridge - I did, connected, distance about 3-4 meters
5. connected the 82 Ohm resistor to the blue cable
6. connected wires like explained in the diagram
7. connected Opener to the cabling
8. started to configure Opener with Generic / Bus Golmar Plus (Beta)
9. got the following dialog after the initial steps and after the bridge was successfully connected (step 4)
   
   
10. connected again to the bridge
11. same issue again → LOOP here so I decided to continue anyway
12. now I got the following screen:
    
    
13. tried again, same…
14. tried other configuration types as show on the config screens (what about the yellow and red cable connection first ti (D) then on another try to (-) which does not fit to the wiring layout in the PDF…

I stopped here as it seem that either I am missing something or the configuration dialog does not realize the wiring as mentioned in the pdf file here: https://developer.nuki.io/t/golmar-plus-intercom-system-support/4017

Any help appreciated, as I would really love to have this working!

Thanks,
Chris

[Georg_S (Georg Sixt)]

Hi, I just realized, there was a mistake in the configuration data for the Golmar profile. I kindly ask you to try a reconfiguration. Thank you!

[Michiel (Michiel Panders)]

Hi Georg, I connected mine and had some challenges with the bridge connection that dropped when starting configuring the Opener. I managed to circumvent this by first going to “ Manage devices > -Opener > “ My Openere” > connection status and disconnect the bridge and than reconnect.

After that I was able to configure “ My opener” . However , for some reason it does not recognise the doorbel ringing and opening doesn’t work either. It did recognise the “door unlock” passend on the Intercom during the configuration proces.

I wired it according the PDF : So in the picture below of the original wiring , I attached he blue wire plus 82 Ohm resistor to17 , the black to 16 ( these have continuous 18v) , the purple and the red to 9. It is a Golmar Tekna Plus v2

Any idea what I should check or try ?

Thanks & Merry Christmas,

Michiel